Extron-electronics SME 100 User Guide Uživatelský manuál Strana 114
- Strana / 185
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Applying an EDID to an Input Device
Use the following procedure to apply an EDID to an input device connected to the SME100
using the Advanced Settings page (see figure 83).
2
3
4
5
Figure 83. Advanced Settings Page — Applying EDID
1. If necessary, connect an input device to the 15-pin HD connector (input 2) or the
DVI connector (input 3) located on the rear panel of the SME100 (see the "Rear Panel
Features" section on page 12).
2. Use the Select Input radio buttons to select the desired input (input 2 or input 3) to
apply EDID to.
3. From the Resolution drop-down menu, select the desired EDID resolution.
NOTES:
• Saved (custom) EDID can also be selected. For information on creating a
custom EDID, see the "Creating a Custom EDID" section on page 107.
• If a custom EDID has not been captured, the resolution and refresh rate defaults
to 1024x768 @ 60 Hz.
4. From the Refresh Rate drop-down menu, select the desired EDID refresh rate.
NOTE: If a custom EDID is selected from the Resolution drop-down menu, the
Refresh Rate drop-down menu cannot be used. The custom EDID uses the
refresh rate that was captured from the output device.
5. Click the Load button to apply the EDID to the selected input device.
SME100 • Web-based Configuration Page 108
- User Guide 1
- Safety Instructions 2
- FCC Class A Notice 3
- Specifications Availability 4
- Contents 5
- SME 100 • Contents vi 6
- Introduction 7
- SME100 • Introduction 2 8
- Suggested PC Requirements 9
- Features 10
- SME100 • Introduction 5 11
- SME100 • Introduction 6 12
- Definitions 13
- SME100 • Introduction 8 14
- SME100 • Introduction 9 15
- SME100 • Introduction 10 16
- STREAMING MEDIA ENCODER 17
- S-video (YC) 18
- Balanced Audio Output 19
- Unbalanced Audio Output 19
- Connected RS-232 20
- Device Pins 20
- Modes 4 and 5 21
- Hardware Setup Overview 23
- SME100 Power Up Procedure 24
- SME100 Network 25
- Configuration 25
- Protocols Used for Streaming 26
- SME 100 sends data to 27
- Front Panel 28
- Operation 28
- select a submenu option 29
- User Presets 30
- Encode Presets 31
- Streaming Presets 32
- 00000 00000 37
- 0640 0480 37
- 064 064 37
- • Video / Audio 39
- • Video only 39
- 1 to 30. The default is 30 40
- Stream Config Menu 41
- Advanced Config Menu 42
- About the Auto Memory Submenu 44
- About the Auto Image Submenu 46
- Comm Settings Menu 49
- IP), subnet mask (SM), and 50
- GM) submenus (see figure 25) 50
- Settings menu 50
- Default Display Cycle 51
- Web-based User 52
- Interface Operation 52
- SME100 Media Players 53
- Live View Page 54
- Stop button 55
- Live View Page Notifications 56
- Installing Media Players 57
- Windows (see figure 32) 58
- Run to begin the download 59
- Next to 60
- OK (see figure 44) 64
- Next (see figure 45) 65
- Next (see figure 46) 65
- Install 66
- Using VLC 70
- Tools menu, select 71
- Video Effects tab and under 71
- Using QuickTime Media Player 72
- Status Page 73
- Configuration Page 75
- File Management Page 75
- Adding Directories 77
- Uploading Files 78
- Saving Files 78
- Managing Files Using FTP 79
- Backup / Restore Page 80
- Control Page 83
- 2a 2b 2c 2d 2e 2f 2g 2h 2i 84
- User and Input Presets 88
- Saving or recalling presets 89
- Renaming presets 89
- Web-based 90
- System Settings Page 91
- II) [RFC 1213] 93
- Encoder Settings Page 94
- Using Encoding Presets 102
- Using Streaming Presets 103
- Live View Settings Page 104
- Embedding the SME100 Stream 107
- Port Settings Page 109
- Advanced Settings Page 111
- Creating a Custom EDID 113
- Matrix Switcher Syncing 115
- Advanced Settings 117
- Disabling Sync to Matrix 118
- Security Page 119
- Firmware Upgrade Page 121
- Reset Page 122
- Communication and 123
- Software Overview 124
- Installing the software 125
- Running DataViewer 125
- Enter SIS 126
- Commands 126
- Responses 126
- USB tab 128
- Using Telnet 129
- SME100-initiated Messages 130
- Error Responses 131
- 06 / 14 / 11 – 13 : 40 : 03 136
- 137
- SME-100-HD/SD-00-02-3D 138
- E13 error 138
- View GMT offset 153
- Set daylight savings 153
- 192.168.254.254, and the 159
- 255.255.0.0 159
- Power Save Mode 161
- Reference 162
- Information 162
- Streaming Playback Methods 163
- 192.168.254.254 164
- Please enter a network URL 165
- (SAP) (see figure 108) 167
- Available Unicast Streams 170
- Available Multicast Streams 171
- IP Addressing 172
- Subnet Mask 173
- Port Number 173
- Choosing IP Addresses 173
- Response Messages 174
- Pull streaming (RTSP) 175
- SME100 Firmware Updates 176
- Browser Configuration 178
- Sites button and allow the 179
- Plugin Compatibility 182
- Player Compatibility 183
- Media Server Compatibility 183
- Mounting the SME100 184
- Contact Information 185
- Extron Warranty 185
Související produkty a manuály pro Hardware Extron-electronics SME 100 User Guide
(2 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce