Extron electronics QGE 100 Uživatelská příručka

User GuideQGE 100 Graphics EncodersQuantum Graphics Encoder68-2178-01 Rev. A01 12

QGE 100 • Introduction 4Viewing the QGE 100 Data StreamStreamed QGE 100 data can be decoded and displayed using any of the following viewing platforms

QGE 100 • Introduction 5EDID ManagementExtended display identification data (EDID) is a communications protocol or instruction set for the identificat

QGE 100 • Introduction 6Supported Source FormatsThe table below lists the resolutions and refresh rates supported by the QGE 100.Source Resolution Dig

QGE 100 • Introduction 7Application DiagramsCOM 1OUT INCOM 2DVI-I DVI-I12V DCREG 1.5A MAXPERIPHPC Refer all servicing to qualified servic

QGE 100 • Installation and Operation 8Installation and OperationThis section provides the steps to install the QGE 100. It also describes the front an

QGE 100 • Installation and Maintenance 9Rear Panel FeaturesCOM 1OUTINCOM 2DVI-I DVI-I12V DC INREG 1.5A MAXPERIPH PC Refer all servicing

QGE 100 • Installation and Maintenance 10Connecting the Source Computer to the QGE 100Video data from the source computer is streamed over the network

QGE 100 • Installation and Maintenance 118 Analog V-sync 16 Hot plug detect 24 TMDS clock– PinSignalPin SignalPinSignal1 TMDS data 2– 9 TM

QGE 100 • Installation and Maintenance 122. Plug the DVI-A connector of the adapter into the QGE DVI-I Out port. Analog MonitorAnalog to DVI AdapterT

QGE 100 • Installation and Maintenance 132. When the QGE 100 encoder is delivered, the following default addresses are set for it: • IP address: 172

This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipmen

QGE 100 • Installation and Maintenance 14CAUTIONS: • Do not permanently fix the power supply to the building structure or similar structures.• Do not

QGE 100 • Installation and Maintenance 15Connections with a Digital SourceCOM 1OUT INCOM 2DVI-I DVI-I12V DC INREG 1.5A MAXPERIPH PC Refe

QGE 100 • Installation and Maintenance 16Connections with an Analog Source Analog MonitorDVI-A to 15-pin HD AdapterCOM 1OUT INCOM 2DVI-I DVI-I12V DC I

QGE 100 • Installation and Maintenance 17Front Panel FeaturesSTATUSLANQGE 100QUANTUM GRAPHICS ENCODER123Figure 12. QGE 100 Front PanelThe QGE 100 fron

QGE 100 • Software Configuration and Control 18Software Configuration and ControlThis section describes the QGE 100 software programs and provides proc

QGE 100 • Software Configuration and Control 19Installing the Software The Administrator software and Viewer software programs for the QGE 100 are pro

QGE 100 • Software Configuration and Control 202. In the QGE 100 List section, select one of the listed QGEs by clicking on its name to highlight it.

QGE 100 • Software Configuration and Control 21QGE 100 List sectionThe QGE 100 List section displays information on all QGEs detected by the Administr

QGE 100 • Software Configuration and Control 22Configure QGE 100 Properties sectionThe QGE 100 Properties section provides fields in which you can sele

QGE 100 • Software Configuration and Control 23Tools menuOption DescriptionMouse and Keyboard OptionsOpens a window that lets you set some parameters

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule

QGE 100 • Software Configuration and Control 24Viewing a QGE 100 SourceThe QGE 100 Administrator provides a Viewer window on which you can view a conn

QGE 100 • Software Configuration and Control 25The Administrator Viewer window contains a menu bar and a toolbar from which you can specify parameters

QGE 100 • Software Configuration and Control 26Managing the QGE 100 ListYou can perform the following tasks on the QGE 100 List:Refreshing the listAft

QGE 100 • Software Configuration and Control 272. Enter the requested information in the text elds, then click OK.Figure 16. Add QGE 100 WindowDelet

QGE 100 • Software Configuration and Control 28Logging In and Out (Administrator Level)By default, you are logged in at user level when you first open

QGE 100 • Software Configuration and Control 29Configuring a QGE 100The Configure QGE 100 Properties section of the main window contains fields in whic

QGE 100 • Software Configuration and Control 30Figure 22Figure 22. Network Settings WindowThe table below lists and describes the network settings tha

QGE 100 • Software Configuration and Control 31Configuring UDP multicast settingsTo use a Quantum Elite processor as a viewing device or to connect the

QGE 100 • Software Configuration and Control 32Configuring the QGE for Use with a Quantum Elite ProcessorTo use a Quantum Elite Videowall Processor as

QGE 100 • Software Configuration and Control 33Example:Figure 25. Set Up Sources Screen on the Quantum Control Software Main WindowFor detailed inform

Conventions Used in this GuideNotificationsIn this user guide, the following are used:CAUTION: A caution indicates a potential hazard to equipment or

QGE 100 • Software Configuration and Control 34Using the QGE 100 Viewer ProgramThe QGE 100 Viewer software displays QGE 100 sources on your viewing co

QGE 100 • Software Configuration and Control 35The QGE 100 Viewer WindowFigure 26. QGE 100 Viewer Main WindowThe main window of the QGE 100 Viewer con

QGE 100 • Software Configuration and Control 36Menus and toolbarThe QGE 100 Viewer window contains a menu bar and a toolbar from which you can specify

QGE 100 • Software Configuration and Control 37View menuOption Toolbar Icon DescriptionRefresh Channel ListUpdates the information in the Channel (QGE

QGE 100 • Software Configuration and Control 38Tools menuOption DescriptionMouse & Keyboard Toggles mouse and keyboard control on and off (see “Mo

QGE 100 • Software Configuration and Control 39Connecting using the Connect dialog boxTo connect to a QGE by entering its name or IP address in the Co

QGE 100 • Software Configuration and Control 40Learning DialogsLearning dialogs are pop-up windows that the Administrator and QGE 100 Viewer programs

QGE 100 • Software Configuration and Control 41Mouse and Keyboard Control of the Source ComputerThe keyboard and mouse of the computer that is running

QGE 100 • Software Configuration and Control 422. Enter any desired values in the elds as described in the table below:Field To enter a value:Key Co

QGE 100 • Software Configuration and Control 43Starting and stopping a mouse and keyboard control session• To start a session in which your viewing c

ContentsUsing the QGE 100 Viewer Program ... 34Starting the Viewer Program ... 34The QGE 100 Viewer Window ...

QGE 100 • Software Configuration and Control 44Using the Special Context menuThe Special Context pop-up menu contains commands that you can select to

QGE 100 Series Videowall Processing Systems • HTML Operation 45QGE 100 • Reference Information 45Reference InformationThis section contains reference

QGE 100 • Reference Information 4646Ethernet data rate ... 10/100Base-T, half duplex with autodetectEthernet protocol ...

QGE 100 • Reference Information 4747Part Numbers and AccessoriesThe following tables list the items that are shipped with the QGE 100, or can be order

QGE 100 • Reference Information 4848Mounting the QGE 100 EncoderThe QGE 100 encoder can be placed on a tabletop or mounted in a rack.NOTE: Always use

QGE 100 • Reference Information 4949IP AddressingWhat is an IP Address?A full explanation of IP addressing is beyond the scope of this user guide. How

QGE 100 • Reference Information 5050The following is an example of an invalid Class C addressing scheme:Device IP AddressQGE 100 viewing computer 208.

QGE 100 • Reference Information 51514. At the command prompt, enter ping IP address. The computer returns a display similar to the figure below.The Pi

QGE 100 • Reference Information 5252IP addresses and octetsValid IP addresses consist of four 1-, 2-, or 3-digit numeric sub-fields, called “octets,”

QGE 100 • Reference Information 5353Troubleshooting PerformanceIn an ideal QGE 100 system, the source displayed on the viewing device should be virtua

QGE 100 • Contents vi

QGE 100 • Reference Information 5454TIP: In addition to the improved image quality that digital sources provide, they are also more efficient on enco

QGE 100 • Reference Information 5555Optimizing the Encoder ParametersUsing the QGE 100 Administrator software, you can set the parameters listed below

Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.863.1794 +1.714.491.1517 FAX +

QGE 100 • Introduction 1IntroductionThis section gives an overview of the Extron QGE 100 Quantum Graphics Encoder, describes its significant features,

QGE 100 • Introduction 2POWERQUANTUM ELITEDATASource PCNetwork SwitchPC Running ViewerSoftwareQGE 100 Quantum Graphics EncoderQuantum Elite Videowall

QGE 100 • Introduction 3FeaturesThe QGE 100 features the following: • Allows simple connection of a DVI or RGB source to an IP network. • Streams st