Extron electronics System 10 Plus Provozní pokyny Strana 22
- Strana / 74
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Installation, cont’d
System 7SC • Installation2-10
The pin assignments are as follows:
Signal
Display power/current sensor detection
Carrier & signal
Gnd
+12 V
E
D
C
B
A
Wire the connector using one of the following wiring options.
D
C
E
D
C
D
A
IR Emitter
White Striped Wire Only
100'
(30.5 m)
(Demodulated IR)
Carrier & Signal
Gnd*
System 7
IR Comm
Port
For the IR Emitter only
IR COMM
ABCDE
Carrier & signal
Gnd
Gnd
+12 V
System 7
IR Comm
Port
For the IR Broadcaster with emitter port
IR COMM
ABCDE
Signal
System 7
IR Comm
Port
For a wired projector remote port
IR COMM
ABCDE
To the projector's
wired remote port
(Connector type
and pin
configurations may
vary depending on
the projector
model.)
To IR Broadcaster
with emitter port
(#60-272-02)
IR Communications port wiring options
For some projectors the emitter must be used together with the IR Broadcaster.
Refer to the IR Broadcaster User’s Guide (part #68-392-02) or contact an
Extron support representative for details.
6
Projector control port — Connect a cable between the projector and this
3.5 mm, 10-pole captive screw connector for RS-232 or RS-422 one- or two-
way projector/display device control. Commands from a downloaded
projector control program or user-defined command strings entered via the
Windows-based control program can be sent to the display device from this
port.
Use the following illustration as a guide to wiring the connector. Wiring will
vary depending on the projector model. In most cases only the transmit (Tx)
and ground connections will be needed.
- System 7SC 1
- Inside front cover: 2
- Table of Contents 3
- Table of Contents, cont’d 4
- FCC Class A Notice 5
- Chapter One 7
- Introduction 8
- 1-3System 7SC • Introduction 9
- Introduction, cont’d 10
- Options and accessories 11
- Chapter Two 13
- Installation 14
- SYSTEM 7SC 15
- Installation, cont’d 16
- 2-5System 7SC • Installation 17
- Rear panel inputs 17
- 2-7System 7SC • Installation 19
- Ground (shield/drain) 20
- Ground (black) 20
- Comm. signal (white) 20
- +12 VDC (red) 20
- 2-9System 7SC • Installation 21
- PROJ CONTROL 23
- System 7SC Rear Panel 25
- Slave Switcher 25
- Rear Panel 25
- 2-15System 7SC • Installation 27
- Installing the software 27
- Using the software 27
- Chapter Three 29
- Operation and Configuration 30
- If Display Power is on 31
- Adjustment features 32
- Input selection features 33
- Miscellaneous features 33
- Projector control memory 34
- Optimizing the System 35
- Menu overview 36
- Switcher Setup/Configuration 37
- Edge Smoothing 39
- Add Slave (slaving switchers) 39
- Audio/Video Adjustments 40
- Audio Level 41
- Image Size 41
- Size Input 41
- IR Learning Configuration 42
- Initiating IR learning 44
- Information/System Options 45
- Image adjustments 45
- Centering 46
- SCP control pads 47
- Selecting an input 48
- Chapter Four 49
- Serial Communication 50
- Serial Communication, cont’d 52
- Vid, Y-C, YUV, YUVp, or RGB) 53
- Audio settings 57
- IR-related settings 57
- Miscellaneous settings 57
- Control Software for Windows 59
- Real Time Adjustments 61
- Room & Misc. Options 63
- Appendix A 65
- Reference Material 66
- Audio input 67
- Audio output 67
- Reference Material, cont’d 68
- Part Numbers and Accessories 69
- Extron’s Warranty 73
- Inside USA / Canada Only 74
- Inside Europe Only 74
- Inside Asia Only 74
- Inside China Only 74
Související produkty a manuály pro Síťové přepínače Extron electronics System 10 Plus
(42 stránky)
Eden W1550 manuels
Manuels d'utilisation et guides de l'utilisateur pour Audio Eden W1550.
Nous fournissons des manuels en pdf 1 Eden W1550 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentáře k této Příručce