Extron-electronics MTP Series User Guide Uživatelský manuál

User GuideMTP SeriesTwisted PairVideo and Audio Twisted Pair Transmitters and Receivers68-732-01 Rev. H11 11

MTP Series • Installation 4Setting the Jumpers on Non AAP Models1. Remove and retain the four screws (two on each side of the unit) that secure the

MTP Series • Installation 55. Locate the jumper blocks (see figure 3) on the video board. Shift the jumper to the alternate location.Transmitter Fro

MTP Series • Installation 6Setting the Jumpers on AAP Transmitters1. Remove and retain the two screws that secure the back cover to the MTP (see fig

MTP Series • Installation 7Mounting OptionsUL RequirementsThe following Underwriters Laboratories (UL) requirements pertain to the installation of th

MTP Series • Installation 8Rack ShelfQuarter Rack WidthFalse Front Face Plate (2) 4-40 x 3/16"ScrewsEighth Rack WidthFalse Front Face Plate Figu

MTP Series • Installation 93. For furniture mounting —a. Hold the MTP with the attached brackets against the underside of the mounting surface. Mar

MTP Series • Installation 10Panel Features and ConnectionsTransmitter Input ConnectionsFigure 12 shows all of the combinations of video and audio inp

MTP Series • Installation 11CAUTIONS: • The length of the exposed (stripped) portion of the copper wires is important. The ideal length is 3/16 inch

MTP Series • Installation 12Transmitter and Receiver Throughput ConnectionsFigure 16 identifies the connections between the transmitter and receiver.

MTP Series • Installation 13TP cable terminationFigure 17 details the recommended termination of TP cables with RJ-45 connectors in accordance with t

This symbol is intended to alert the user of important operating and mainte-nance (servicing) instructions in the literature provided with the equipme

MTP Series • Installation 14f Power connector — Plug the external 12 VDC power supply into this 2-pole captive screw connector on both the transmitt

MTP Series • Installation 15Receiver Output ConnectionsSee figure 20 to identify the receivers rear panel output connections. The figures show all of

MTP Series • Operation 16OperationThis section describes:• Front Panel Features• Troubleshooting — Skew Delay CompensationFront Panel FeaturesSHARPC

MTP Series • Reference Information 17Reference InformationThis section provides information on:• Specifications• Part Numbers SpecificationsVideoGai

MTP Series • Reference Information 18SyncStandards ... NTSC 3.58, NTSC 4.43, PAL, SECAMAudio GainRCA models ...

MTP Series • Reference Information 19GeneralRecommended cable type ... CAT5/5e/6 (shielded or unshielded)External power supply ...

MTP Series • Reference Information 20Part NumbersMTP TransmittersDescription Part NumbersMTP T SV A 60-540-52MTP T SV A RCA 60-540-62MTP T SVA AAP (b

MTP Series • Reference Information 21Cables and ConnectorsNOTE: Enhanced Skew-Free™ A/V UTP cables are not recommended for Ethernet/LAN applications

Extron WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purc

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rule

Conventions Used in this GuideIn this user guide, the following are used:NOTE: A note draws attention to important information.TIP: A tip provides a

ContentsIntroduction... 1About the MTP Transmitters and Receivers ... 1TP Cable Advant

MTP Series • Contents vi

MTP Series • Introduction 1IntroductionThis section introduces the MTP transmitters and receivers. Topics discussed in this section are:• About the M

MTP Series • Introduction 2TP Cable AdvantagesTwisted pair (TP) cable is much smaller, lighter, more flexible, and less expensive than coaxial cable.

MTP Series • Installation 3InstallationThis section describes the installation procedures, including: • Signal Jumpers for Generational Compatibility