Extron electronics CS 120P Uživatelská příručka Strana 1

User GuideCS 3T and CS 120PSpeakersCS 123T SpeedMount Ceiling Speaker System68-2543-01 Rev. A01 15CS 3T and CS 120P User Guide

Installing the CS 123T System — Single InstallerIf a single installer is installing the CS 123T system, follow this procedure for the entire system:NO

e. Cut out the circle traced in the ceiling tile.f. Replace the tile in the ceiling.4. Remove the adjacent ceiling tile — To facilitate the instal

6. Configure the CS 120P for a U.S. or metric ceiling grid — For U.S. ceilings (2 feet by 2 feet or 2 feet by 4 feet), leave intact the four tabs th

Rear of EnclosureFlexible ConduitFlexible Conduit AdapterCover PlateSecondary Cable PassThrough Loop with flexible conduitFigure 7. Routing the Cable

9. Wire the CS 120P — Route the wires through the H-shaped opening in the CS 120P. Be sure to leave sufficient slack. Figure 9. Route the Wires Th

12. Place the CS 120P into the ceiling grid — Place the CS 120P over the tile grid so that the CS 120P is safely supported on the two short edges. En

15. Remove the speaker grille — Carefully remove the grille from the front of the CS 3T.NOTE: Grille hooks are provided for grille removal, if neede

The source signal can be tested by connecting to the inner + (IN) and – (IN) terminals of the captive screw connector.Signal Test PointsRed Wire (+) f

• The impedance of the speakers downstream of the one being tested can be measured while the system is on by connecting to the outer (LOOP) terminals

18. Attach the speaker wire to the strain relief tie down point using the provided zip tie. Zip TieStrain ReliefTabFigure 20. Attaching the Speaker

Safety InstructionsSafety Instructions • EnglishWARNING: This symbol, , when used on the product, is intended to alert the user of the presence of u

20. Mount the CS 3T (see figure 21).a. Insert the CS 3T through the bottom of the hole in the ceiling tile that was cut in step 3. b. Tighten the fo

21. Attach the secondary support line (open back configuration) — Attach the secondary support line as shown in figure 22.ATTENTION: • Do not allow a

ATTENTION: • When setting the taps for a distributed (high impedance) system, do not tap the system above the rated power of the amplifier. • Lors de

Installing the CS 120P in a Suspended Ceiling — Division of LaborIn a division of labor installation, low-voltage contractors install the CS 120P encl

4. Cut a hole for the CS 3T speaker. Use the provided cutout template to outline the hole to be cut in the ceiling tile as described below. (If the

7. Route the cables through the cover plate — NOTES: • The CS 120P is fully UL 2043 compliant only when it is used with a metal conduit or with p

8. Wire the CS 120P — Route the wires through the H-shaped opening in the CS 120P. Be sure to leave sufficient slack.Figure 30. Route the Wires Thr

11. Place the CS 120P into the ceiling grid — Place the CS 120P over the tile grid so that the CS 120P is safely supported on the two short edges. If

NOTE: The zip tie located in the CS 120P must be attached to the driver assembly.13. Replace the adjacent tile — Reinstall the adjacent tile if one w

5. Attach the speaker wires to the captive screw connector — ATTENTION : • Do not tin the wires. Tinned wires are not as secure in the connector a

FCC Class A NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the FCC rule

The source signal can be tested by connecting to the inner + (IN) and – (IN) terminals of the captive screw connector.Signal Test PointsRed Wire (+) f

• The impedance of the speakers downstream of the one being tested can be measured while the system is on by connecting to the outer (LOOP) terminals

7. Attach the speaker wire to the strain relief tie down point using the provided zip tie. Zip TieStrain ReliefTab Figure 41. Attaching the Speaker

9. Mount the CS 3T (see figure 42).a. Insert the CS 3T through the bottom of the hole in the ceiling tile that was cut in step 2. b. Tighten the fo

11. Install the grille — Position the outer perimeter of the grille into the groove of the speaker baffle. Six magnets pull the grille securely into p

Installing the CS 120P in a Hard CeilingIf you are installing the CS 123T in a hard ceiling (having no ceiling tiles), with the ceiling structure in p

Painting the Grille1. With the grille detached from the speaker, carefully remove the scrim from the inner side of the grille.2. Carefully remove th

Extron Headquarters+1.800.633.9876 (Inside USA/Canada Only)Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +

Conventions Used in this GuideNotificationsThe following notifications are used in this guide:WARNING: Potential risk of severe injury or death. AVER

ContentsIntroduction... 1About this Guide ... 1

IntroductionThis section gives an overview of the Extron CS 123T SpeedMount Ceiling Speaker System, consisting of the CS 3T speakers and CS 120P enclo

Features• Patented two-piece speaker system for suspended ceilings in division-of-labor installations — • CS 120P plenum ceiling tile enclosure, 1’

Application ExampleThe illustration below is one example of configuring a system using the CS 123T.100-240V ~ -- A MAX1CONFIGURABLEHDMI HDMI58CRS-232 I

InstallationThis section provides instructions for installing the CS 3T speakers and the CS 120P enclosure. Topics include:• Installation Considerati