Extron-electronics Annotator User Guide Uživatelský manuál Strana 103
- Strana / 108
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Ethernet
Connection
This section describes connection to the Ethernet.
Ethernet Link
The rear panel Ethernet connector on the Annotator can be connected to an Ethernet
LAN or WAN. This connection makes SIS or software control of the unit possible using a
computer connected to the same LAN.
Ethernet Connection
The Ethernet cable can be terminated as a straight-through cable or a crossover cable and
must be properly terminated for your application.
• Crossover cable — Direct connection between the computer and the Annotator.
• Patch (straight) cable — Connection of the Annotator to an Ethernet LAN.
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
12345678
Straight-through Cable
(for connection to a switch, hub, or router)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-orange
2 orange 2 orange
3 white-green 3 white-green
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 green
7 white-brown 7 white-brown
8 brown 8 brown
Crossover Cable
(for direct connection to a PC)
End 1 End 2
Pin Wire Color Pin Wire Color
1 white-orange 1 white-green
2 orange 2 green
3 white-green 3 white-orange
4 blue 4 blue
5 white-blue 5 white-blue
6 green 6 orange
7 white-brown 7 white-brown
8 brown 8 brown
Figure 58. RJ-45 Connector Pinout Tables
Default Address
To access the Annotator via the Ethernet port, you need the unit’s IP address. If the address
has been changed to an address comprised of words and characters, the actual numeric IP
address can be determined using the ping utility. If the address has not been changed, the
factory-specified default is 192.168.254.254.
Ping can also be used to test the Ethernet link to the Annotator.
Annotator • Ethernet Connection 97
- User Guide 1
- Annotator 1
- Precautions 2
- FCC Class A Notice 3
- Copyright 4
- Trademarks 4
- Contents 5
- Signal Processing 6
- Introduction 7
- Denitions 8
- Features 9
- Annotator • Introduction 4 10
- Annotator • Installation 5 11
- Installation 12
- Rack Mount 13
- Rear Panel 14
- Features and 14
- Connections 14
- RGsB/Component Video 15
- (Y, R-Y, B-Y) 15
- Composite VideoS-video (YC) 15
- RGBS/RGBcvS 15
- Installation and Cabling 16
- Powering Up 17
- Modes 3, 4, and 5 18
- Annotator • Operation 13 19
- Operation 20
- Switching Inputs 21
- Button Backlighting 21
- The Annotator Menu System 22
- ” section 22
- Using the Menus 24
- User Presets 24
- Input Conguration 25
- Output Conguration 26
- Advanced Conguration 27
- To capture an image: 28
- View Comm Settings 29
- Edit Comm Settings 30
- Exit Menu 30
- Scan Converter Conguration 31
- Aux Scaler Conguration 31
- Executive Mode 32
- Disabled 32
- Annotator • Operation 27 33
- Annotator • Operation 28 34
- Take. The devices 35
- Annotator • Operation 29 35
- On Screen 36
- Annotation 36
- USB Port Connections 37
- Touchscreen Calibration 38
- Annotation Overview 39
- Default Annotation Buttons 40
- Communication 43
- Establishing a Connection 44
- Connection Time-outs 44
- Number of Connections 44
- Using Verbose Mode 44
- Processor-Initiated Messages 45
- Symbol Definitions 46
- 1 = Follow, 2 = Fill 48
- (host to processor) 49
- (processor to host) 49
- Picture Adjustments 51
- Output Configuration 53
- Scan Converter Board 53
- Command ASCII command 60
- Response 60
- Additional description 60
- Information request 60
- Command ASCII (Telnet) 63
- URL Encoded (Web) 63
- Response 63
- Additional 63
- Products Control 67
- Installation from the Website 68
- Starting the SPPCP 68
- Using the SPPCP 69
- SPPCP Menus 70
- Tools menu 71
- F1>, or click Help > 72
- Annotator • SPPCP 66 72
- Annotator • SPPCP 67 73
- Annotator • SPPCP 68 74
- To update the firmware: 75
- Help menu 76
- Control Tab 77
- I/O Conguration Tab 78
- Advanced Settings Tab 79
- Scan Converter Tab 80
- Aux Scaler Tab 81
- Image Capture Tab 82
- Font Tab 83
- Status Bar 83
- HTML Operation 84
- Status Tab 85
- Conguration Tab 86
- Annotator • HTML Operation 81 87
- Date/Time Settings fields 88
- Scaler Settings page 89
- Input configuration 89
- Output configuration 90
- Advanced configuration 90
- Annotator • HTML Operation 85 91
- Passwords page 92
- Firmware Upgrade page 93
- Annotator • HTML Operation 88 94
- File Management Tab 95
- Presets page 97
- PIP Page 97
- Images page 98
- Reference 99
- Material 99
- Video output 100
- Control/remote — annotation 101
- Part Numbers and Accessories 102
- Ethernet 103
- Connection 103
- Connect as a Telnet client 104
- Telnet Tips 105
- Subnetting Basics 106
- IP addresses and octets 107
- Subnet masks and octets 107
- Extron Warranty 108
Související produkty a manuály pro Počítačové příslušenství Extron-electronics Annotator User Guide
Počítačové příslušenství Extron-electronics FOX USB Extender Setup Guide Uživatelský manuál
(2 stránky)
(2 stránky)
Počítačové příslušenství Extron-electronics FOX USB Extender User Guide Uživatelský manuál
(19 stránky)
(19 stránky)
Počítačové příslušenství Extron-electronics IPL T Series Setup Guide Uživatelský manuál
(29 stránky)
(29 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce